Locksets & Hardware for Steel Doors in Austin, TX
Looking for high-quality door handles and locksets in Austin? We offer both standard and custom options to match your style and fit your doors perfectly. Every product is made with care and built to last.
Our strong craftsmanship, stylish designs, friendly customer service and affordable prices make us a top choice in Austin for steel and iron door hardware.
Find the best deals on exterior door levers, interior door handles, bedroom and bathroom door levers, closet locksets and more in Austin.
Why Hardware Decides How a Door Performs
The lockset on a door does two jobs, and most people only think about one of them. The obvious job is security. The less obvious one is compressing the weatherseals, because a door seals when its locking hardware pulls it into the gaskets, and how evenly that happens determines whether the door keeps out water, dust and conditioned air.
This is why a single deadbolt in the middle of a tall door is a poor arrangement regardless of how good the deadbolt is. It compresses the seal at one point and leaves the head and sill relatively free, so the top and bottom of the door can move and leak. The taller the door, the more pronounced this becomes.
Multipoint locking solves both problems at once. Engaging the frame at several heights makes the door far harder to force and pulls it uniformly into its seals along the full height. On the large steel doors we build, it is not an upgrade so much as a requirement of the format.
Hardware We Specify
Multipoint locking systems
Hooks, bolts or a combination engaging the frame at several points from a single handle throw. Standard on our larger doors, and the reason they both seal and secure properly.
Deadbolts
Included on every entry door we build. Bolt projection and construction matter more than the visible escutcheon, and they are specified to suit the door rather than chosen by appearance.
Lever and knob sets
A wide range of finishes and styles for both interior and exterior use, matched to the door finish or deliberately contrasted where the design calls for it.
Pull handles and bar handles
Full-height and offset pulls, which are the usual choice on pivot doors and large contemporary entries where a conventional lever would look undersized.
Flush bolts for passive leaves
Head and sill bolts securing the inactive leaf of a pair into the structure, available surface-mounted or concealed in the leaf edge. Essential on double doors.
Smart locks and keyless entry
Electronic deadbolts, keypad entry and connected locks can be integrated where the door construction and lock case allow. This needs to be decided at design stage rather than retrofitted.
What Good Hardware Delivers
Hardware is the part of a door you physically touch every day, and the part that determines whether the rest of it works.
- Real resistance to forced entry. Locking that engages at several heights distributes the load across the door rather than concentrating it at one point that can be levered.
- Weathertight sealing. Even compression around the perimeter is what actually keeps driving rain and Central Texas pollen out of the house.
- Doors that feel right. The weight and action of the handle is the most direct daily experience of a door's quality, and cheap hardware betrays an otherwise excellent door instantly.
- Lower air leakage. A properly compressed seal reduces conditioned air escaping, which matters over a long Texas cooling season.
- Longevity. Hardware sized to the door rather than to a price point continues to operate smoothly through decades of daily cycling.
- Coordinated appearance. Handles, hinges and locking specified together in matched finishes across a project make a house read as considered.
Hardware by Door Type
Different door formats have genuinely different hardware requirements, and matching them properly is part of the design.
Single entry doors
Multipoint locking with a deadbolt and a lever or pull. The standard specification for a steel entry door, giving both security and even seal compression.
Double doors and pairs
Multipoint locking on the active leaf plus concealed or surface flush bolts securing the passive leaf into head and sill. See double entry doors and french doors.
Pivot doors
Full-height pulls and multipoint locking specified to a large slab, with the pivot hardware itself rated above the calculated door weight. Covered on the pivot doors page.
Sliding and folding systems
Hook-bolt multipoint locking that draws panels into their seals, with flush pulls that sit within the stile so nothing catches during travel. See sliding and bifold doors.
Interior doors
Lighter latching, privacy locks for bathrooms and bedrooms, and flush pulls for sliding and pocket doors. Security is not the driver indoors, so the specification is about feel.
Windows
Multipoint locking and crank or lever operators on casement and awning windows, sized to sash weight so they operate smoothly.
How Hardware Is Fitted
Lock cases and hardware are integrated into the door during fabrication rather than cut in afterwards. On a welded steel door the lock preparation has to be planned into the section before assembly, which means the hardware selection is a design decision made early rather than a choice deferred to the end. Retrofitting hardware into finished steel is difficult and rarely tidy.
Every door is hung in its own frame with the hardware fitted and cycled in the shop before finishing. Lock engagement, keeper alignment and seal compression are all set with the actual matched components. A lock that throws freely on the bench may not align with a keeper in a frame that was made separately, and that is exactly the problem that shop assembly eliminates.
Hinges and pivots are specified against calculated door weight with margin rather than to the minimum rating. This is the most common shortcut in door hardware and the source of most doors that begin to drop at the strike edge after a few years. A hinge working at the top of its range is a hinge that will eventually fail.
Finishes are coordinated across the project, and exterior hardware is specified for the exposure it will actually see. A handle in full Central Texas sun on a west-facing entry has a harder life than the same handle under a deep porch, and the finish selection should reflect that rather than assume all positions are equivalent.
Security Considerations by Situation
Front entries
The primary security opening, where multipoint locking plus a substantial deadbolt is the baseline. Glazed areas within reach of the lock should be laminated.
Doors with sidelites
Glazing beside the lock is the classic vulnerability, addressed with laminated glass so the panel cannot be broken through. See doors with sidelites.
Large glazed patio systems
Hook-bolt locking prevents panels being lifted from their tracks, which is the usual method of attack on sliding systems.
Side and rear entrances
Often the least considered and most vulnerable openings on a house, and worth specifying to the same standard as the front door.
Commercial entrances
Higher cycle counts and code requirements around egress hardware, which we specify to suit the occupancy and use.
Smart and keyless access
Convenient and increasingly common, but the mechanical lock underneath still does the security work, so it should not be specified down because there is a keypad on it.
Why Hardware Specification Matters to Us
We include the deadbolt, handles and locking hardware in every door price rather than treating hardware as an extra. That is deliberate. A door quoted without hardware invites a decision made on cost at the end of a project, which is exactly when the wrong choice gets made and the door underperforms for the rest of its life.
Hardware is sized to the door by calculation. Hinges, pivots and locking gear are specified against actual door weight with margin, because components running at their rated limit are what produce doors that sag, stiffen and stop sealing. This is unglamorous and it is most of what determines how a door behaves in year ten.
Because we fabricate and install in house, the hardware is fitted and proven in the shop with the door hung in its own frame, then set on site by the same company. Lock engagement and seal compression survive the journey from shop to opening, which is not guaranteed when fabrication and installation are handled separately.
We work with homeowners, Austin architects and custom builders across the greater Austin area and Central Texas, with projects in Dallas, Houston, San Antonio and Fort Worth. Completed work is shown on our projects page, and fitting is described on the installation page.
Frequently Asked Questions
What is multipoint locking and do I need it?
It is a locking system that engages the frame at several points, usually the head, the sill and mid-height, from a single handle throw. On a large or tall door you do need it, for two reasons: it makes forcing the door substantially harder, and it compresses the weatherseals evenly along the full height. A single deadbolt on a tall door leaves the top and bottom relatively unsealed.
Is hardware included in the price of the door?
Yes. Every door price includes the manufactured door, jamb, glass, threshold, weather stripping, deadbolt, handles and professional installation. We quote it this way so hardware is specified properly as part of the design rather than being value-engineered at the end of a project.
Can I use a smart lock on a steel door?
In most cases yes, but it needs to be decided at design stage. The lock case and the wiring or battery access have to be planned into the door during fabrication, because cutting into a finished welded steel door afterwards is difficult and rarely produces a clean result. Tell us early and we will build for it.
Are glazed doors less secure than solid ones?
Only if the glazing is specified poorly. Laminated glass holds together when struck instead of falling out of the frame, so it cannot simply be broken through to reach the lock inside. With laminated glazing and multipoint locking, a glazed steel door is a secure entry. Our glass options page covers the specification.
What finish should I choose for exterior hardware?
Consider the exposure as well as the appearance. Hardware on a west-facing entry in full Texas afternoon sun has a considerably harder life than the same handle under a deep covered porch. We will recommend finishes that suit the position, and we coordinate finishes across the project so doors and windows read consistently.
How do I stop my door dropping or sticking over time?
Mostly by specifying hinges correctly in the first place, with capacity above the actual door weight. Beyond that, keep the fixings tight and have the hinges adjusted if the door starts to catch. On Austin's expansive clay soils some seasonal movement in the building is normal, which is why we build adjustment range into our frames so a door can be brought back into line during a short service visit.
Can hardware be matched across doors and windows on a project?
Yes, and it is worth doing. Handles, levers, pulls and window operators can be specified in matching finishes across an entire house, including interior doors. Coordinating hardware is one of the less expensive things that makes a project read as deliberately designed rather than assembled piecemeal.
Specify your hardware properly
Tell us about your doors, how they are used and any smart access requirements, and we will recommend a locking and hardware specification and include it in your quote. Serving Austin and Central Texas, with projects across Dallas, Houston, San Antonio and Fort Worth.
